Billy Huddleston wrote:
> Is that v4.1.72 a beta? I can't find it on the USR site at all.
>
> > -----Original Message-----
> > From: emerald-request@iea-software.com
> > [mailto:emerald-request@iea-software.com]On Behalf Of Tom Bilan
> > Sent: Friday, February 12, 1999 5:35 PM
> > To: 'emerald@iea-software.com'
> > Subject: RE: [Emerald] HyperARC and RadiusNT
> >
> >
> > ENH5HIPER>> show pbus set
> > PBUS SETTINGS
> > Reported Base :1
> > Port Density :24
> > ENH5HIPER>>
> >
> > System Version: V4.1.72
> >
> > It works fine for us. I know we had to be patient and wait
> > for the other
> > people to hang up and stuff before it start reporting the
> > right number.
> > Also, don't look at 'list networks', that number is always
> > screwed up. Also
> > make sure you're specifying the right number of ports in emerald.
> >
> > Tom
> >
> > -----Original Message-----
> > From: Billy Huddleston [mailto:billy@nxs.net]
> > Sent: Friday, February 12, 1999 12:09 PM
> > To: emerald@iea-software.com
> > Subject: RE: [Emerald] HyperARC and RadiusNT
> >
> >
> > I did these commands. However, it still seams that only the
> > first HyperDSP
> > will show up on
> > the connection list, anyone on the second card doesn't show
> > up, and from
> > what I can tell,
> > the TC is using something around 1000+ for the NAS address
> > for ports on the
> > second card.
> >
> >
> > > -----Original Message-----
> > > From: emerald-request@iea-software.com
> > > [mailto:emerald-request@iea-software.com]On Behalf Of Tom Bilan
> > > Sent: Friday, February 12, 1999 8:30 AM
> > > To: 'emerald@iea-software.com'
> > > Subject: RE: [Emerald] HyperARC and RadiusNT
> > >
> > >
> > > It's a problem with the HiperARC. Their port numbering is retarded.
> > >
> > > I complained to USR a year ago about this and they added
> > the commands:
> > > SET PBUS REPORTED_BASE
> > > SET PBUS REPORTED_PORT_DENSITY
> > >
> > > USR/3com defaults to 256 per port and if you are running
> > > hiper DSPs you need
> > > to change that to 24. If you're running quad modem cards
> > > it's 4. If you
> > > have both HiperDSPs and Quads in the same chassis they you
> > > need to set it to
> > > 24 (the highest of the two).
> > >
> > > Tom Bilan
> > > TDI Internet
> > >
> > > -----Original Message-----
> > > From: Billy Huddleston [mailto:billy@nxs.net]
> > > Sent: Thursday, February 11, 1999 8:41 PM
> > > To: emerald@iea-software.com
> > > Subject: [Emerald] HyperARC and RadiusNT
> > >
> > >
> > > Just upgraded from a Total Control NetSever to a HyperARC
> > > with HyperDSP
> > > cards and Quad Modem cards.
> > > I've been resarching the archives and find that lots of
> > > people have been
> > > having problems with
> > > the way 3Com does the port numbering. Has anyone figured this
> > > out? My first
> > > 23 modems are
> > > showing up in my online calls okay, but as far as I can tell,
> > > the second
> > > card is about 1000
> > > ports above the first one. Anyone have any ideas? Also, How
> > > are you suppose
> > > to configure the
> > > accounting and radius setup in the TC? I've got it using
> > > Ascend for the
> > > "radius type" and
> > > have Enable Hint Assigned and Enable AcctG checked, (didn't
> > > check the Enable
> > > Acct Interval)
> > >
> > > Thanks, Billy Huddleston
> > >
> > >
> > >
> > >
> > > For more information about this list, including removal,
> > > please see http://www.iea-software.com/maillist.html
> > >
> > > For more information about this list, including removal,
> > > please see http://www.iea-software.com/maillist.html
> > >
> >
> >
> > For more information about this list, including removal,
> > please see http://www.iea-software.com/maillist.html
> >
> > For more information about this list, including removal,
> > please see http://www.iea-software.com/maillist.html
> >
>
> For more information about this list, including removal,
> please see http://www.iea-software.com/maillist.html
For more information about this list, including removal,
please see http://www.iea-software.com/maillist.html