> -----Original Message-----
> From: emerald-request@iea-software.com
> [mailto:emerald-request@iea-software.com]On Behalf Of Tom Bilan
> Sent: Friday, February 12, 1999 5:35 PM
> To: 'emerald@iea-software.com'
> Subject: RE: [Emerald] HyperARC and RadiusNT
>
>
> ENH5HIPER>> show pbus set
> PBUS SETTINGS
> Reported Base :1
> Port Density :24
> ENH5HIPER>>
>
> System Version: V4.1.72
>
> It works fine for us. I know we had to be patient and wait
> for the other
> people to hang up and stuff before it start reporting the
> right number.
> Also, don't look at 'list networks', that number is always
> screwed up. Also
> make sure you're specifying the right number of ports in emerald.
>
> Tom
>
> -----Original Message-----
> From: Billy Huddleston [mailto:billy@nxs.net]
> Sent: Friday, February 12, 1999 12:09 PM
> To: emerald@iea-software.com
> Subject: RE: [Emerald] HyperARC and RadiusNT
>
>
> I did these commands. However, it still seams that only the
> first HyperDSP
> will show up on
> the connection list, anyone on the second card doesn't show
> up, and from
> what I can tell,
> the TC is using something around 1000+ for the NAS address
> for ports on the
> second card.
>
>
> > -----Original Message-----
> > From: emerald-request@iea-software.com
> > [mailto:emerald-request@iea-software.com]On Behalf Of Tom Bilan
> > Sent: Friday, February 12, 1999 8:30 AM
> > To: 'emerald@iea-software.com'
> > Subject: RE: [Emerald] HyperARC and RadiusNT
> >
> >
> > It's a problem with the HiperARC. Their port numbering is retarded.
> >
> > I complained to USR a year ago about this and they added
> the commands:
> > SET PBUS REPORTED_BASE
> > SET PBUS REPORTED_PORT_DENSITY
> >
> > USR/3com defaults to 256 per port and if you are running
> > hiper DSPs you need
> > to change that to 24. If you're running quad modem cards
> > it's 4. If you
> > have both HiperDSPs and Quads in the same chassis they you
> > need to set it to
> > 24 (the highest of the two).
> >
> > Tom Bilan
> > TDI Internet
> >
> > -----Original Message-----
> > From: Billy Huddleston [mailto:billy@nxs.net]
> > Sent: Thursday, February 11, 1999 8:41 PM
> > To: emerald@iea-software.com
> > Subject: [Emerald] HyperARC and RadiusNT
> >
> >
> > Just upgraded from a Total Control NetSever to a HyperARC
> > with HyperDSP
> > cards and Quad Modem cards.
> > I've been resarching the archives and find that lots of
> > people have been
> > having problems with
> > the way 3Com does the port numbering. Has anyone figured this
> > out? My first
> > 23 modems are
> > showing up in my online calls okay, but as far as I can tell,
> > the second
> > card is about 1000
> > ports above the first one. Anyone have any ideas? Also, How
> > are you suppose
> > to configure the
> > accounting and radius setup in the TC? I've got it using
> > Ascend for the
> > "radius type" and
> > have Enable Hint Assigned and Enable AcctG checked, (didn't
> > check the Enable
> > Acct Interval)
> >
> > Thanks, Billy Huddleston
> >
> >
> >
> >
> > For more information about this list, including removal,
> > please see http://www.iea-software.com/maillist.html
> >
> > For more information about this list, including removal,
> > please see http://www.iea-software.com/maillist.html
> >
>
>
> For more information about this list, including removal,
> please see http://www.iea-software.com/maillist.html
>
> For more information about this list, including removal,
> please see http://www.iea-software.com/maillist.html
>
For more information about this list, including removal,
please see http://www.iea-software.com/maillist.html